-
Step 1: Match the Serial Number to the Machine—and the Paperwork
-
Step 2: Cold Start (Do Not Let Them Warm It Up First)
-
Step 3: Hydraulic System—Look for Weeping, Feel for Response
-
Step 4: Undercarriage and Tires
-
Step 5: Electrical System and Stored Error Codes
-
Step 6: Attachments and Quick Coupler
-
Step 7: Service Records and Parts Availability
-
Step 8: Load Test
-
What I'd Add for a Terex 750 Chipper Specifically
-
Final Notes (and the Mistakes I Still See)
I've bought 14 used Terex machines since 2019—loaders, chippers, and one excavator I still regret. Three of those purchases went sideways. Combined damage: roughly $4,200 in rework, parts, and one very awkward conversation with my boss. Or rather, closer to $4,500 when I add the transport fees I forgot to count.
So in early 2023, I sat down and built a checklist I now refuse to skip. Eight steps, in the order I actually run them. This isn't a theoretical list pulled from a forum—it's what I do before I hand over a deposit on any used Terex loader for sale, whether it's sitting in a dealer lot or on a private seller's gravel pad.
Most steps take five minutes or less. One of them—the cold start—is the step almost everyone skips, and it's saved me the most money. If you're evaluating a used loader or a Terex 750 chipper and you don't have a mechanic on speed dial, this is for you.
Step 1: Match the Serial Number to the Machine—and the Paperwork
Before anything else: find the serial plate, photograph it, and compare it to the bill of sale, service records, and any financing documents.
In 2021, I bought a loader from a dealer who swore it was a 2019 unit. The serial plate said 2017. The paperwork said 2019. When I pointed out the mismatch, the dealer said "must be a typo." It wasn't a typo. I walked away—but only because I checked. That five-minute step saved me from overpaying by roughly $6,000.
Pass/fail: Serial number matches paperwork. If it doesn't, treat every other claim the seller makes as suspect.
Step 2: Cold Start (Do Not Let Them Warm It Up First)
This is the step most buyers skip. They show up, the seller has the machine idling "because it's cold out," and they climb on for a test drive. By then, the engine's warm.
Warm engines hide problems. A cold diesel that starts rough, smokes white or gray for more than a few seconds, or struggles to hold idle is telling you something a warm engine won't.
Tell the seller—politely—that you need to see a cold start. If they push back ("it's been sitting, it might not fire right away"), that's information too. In my experience, a seller who won't let you see a cold start is hiding something.
I learned this in April 2022, when I bought a used loader that started fine on a warm day. It started fine for three weeks. Then winter hit, and the cold-start issue turned into a $1,100 injector job I hadn't budgeted for.
Pass/fail: Starts within 5–8 seconds of cranking, no excessive smoke after the first few seconds, holds idle without surging.
Step 3: Hydraulic System—Look for Weeping, Feel for Response
Walk around the machine with a flashlight. Check every cylinder, hose fitting, and hydraulic tank seam. A light dusting is fine. A wet sheen is not.
"Weeping" hydraulic fittings are the classic used-equipment problem. They don't leak enough to leave a puddle, but they'll cost you $400–$800 in labor and seals sooner than you'd like.
Then run the functions. On a loader: raise and lower the bucket, tilt it through full range, turn the steering wheel lock-to-lock. Listen for groaning or hesitation. On a chipper like the Terex 750, run the feed rollers and check for smooth engagement.
Pass/fail: No wet sheen on cylinders or fittings. Smooth, predictable response with no groaning under load.
Step 4: Undercarriage and Tires
Wheel loader: check tire wear patterns. Uneven wear on the front tires usually means alignment issues or operator abuse. Tracked machine: measure track sag and check for cracked or missing lugs.
I once missed a bent rim on a rear axle. It looked fine with the machine parked. The tire had a slow leak that only showed up under load. That mistake cost me $650 for a replacement rim and tire—plus two days of downtime I hadn't planned for.
Pass/fail: Even tire wear. No bent rims. Track lugs intact if tracked. If anything looks off, price the replacement before you negotiate.
Step 5: Electrical System and Stored Error Codes
Turn the key to the "on" position without starting. Every dash light should illuminate, then go out. A dead light or a warning that stays on is a problem.
If the machine has a display panel, scroll through the diagnostics menu. Many Terex loaders and chippers store error codes even after the warning light clears. Look specifically for stored codes tied to the transmission, hydraulics, or engine.
Pass/fail: All dash lights illuminate and clear. No stored fault codes related to major systems.
Step 6: Attachments and Quick Coupler
If the machine comes with a bucket, forks, or a quick coupler, test every function. A worn quick coupler runs $1,500 to replace. A bent attachment is often hidden by the way it sits on the ground.
For chippers: check the feed roller teeth and anvil clearance. A worn anvil is cheap to swap. A bent feed roller is not.
Pass/fail: Coupler locks and unlocks smoothly. Attachments sit flush. Chipper feed rollers engage without binding.
Step 7: Service Records and Parts Availability
Ask for service records. If the seller doesn't have them, assume the worst-case maintenance schedule and price accordingly.
Then—and this is the step I wish I'd done sooner—check parts availability for the specific model. Terex has a global parts network, but older or less common models can have long lead times. If the machine needs a part that takes six weeks to ship, that's a six-week downtime risk you're buying into.
I call a dealer or parts supplier before I commit. Ten minutes on the phone, and it's saved me from at least one bad purchase.
Pass/fail: Service records exist (or you've priced the risk). Critical parts—filters, hoses, pumps—are available within a reasonable timeframe.
Step 8: Load Test
A test drive is not a load test. Fill the bucket to capacity—or feed the chipper with the material you'll actually run—and work it for at least ten minutes.
Watch the temperature gauge. Listen for new noises under load. Check for leaks after you shut it down and let it sit five minutes.
I skipped this step once. The machine drove fine empty. Under load, the transmission slipped. That was a $2,300 mistake I won't repeat.
Pass/fail: No overheating, no new noises, no leaks after shutdown. If anything changes under load, walk away.
What I'd Add for a Terex 750 Chipper Specifically
The 750 is a different animal from a loader. The checklist above mostly applies, but add these: check clutch engagement, inspect the feed roller springs, and confirm the discharge chute rotates and locks. I've seen two 750s where the chute lock was broken and the seller "forgot" to mention it.
Also—run the chipper with actual material, not just a spin test. A 750 that spins fine empty can bog down under wet hardwood.
Final Notes (and the Mistakes I Still See)
A few things I've learned the hard way:
- Don't trust "it just needs a tune-up." If it just needed a tune-up, the seller would've done it. Price the tune-up at dealer rates before you negotiate.
- Bring a flashlight and a clean rag. You'll look under the machine and check fluid levels. A clean rag on the dipstick tells you more than the seller's story.
- Price the worst-case scenario. If the transmission fails in month two, can you afford the repair? If not, buy a cheaper machine or a newer one. I've watched too many buyers stretch their budget on the purchase price and then have nothing left for the first repair.
One more thing: this checklist worked for me because I buy used equipment with a predictable use pattern—moderate hours, standard applications, and I have a dealer relationship for parts. If you're buying for a seasonal operation with high-hour demands, or if you're in a region where Terex parts are harder to source, the calculus might be different. I can only speak to my situation.
But the cold-start step? That one's universal. Don't skip it.